Jewelry Sample Development, Step by Step

Quick answer: Jewelry sample development is six stages: brief and drawing, CAD model, master and mould, first casting, setting and finishing, then your review before a revision round. Each stage ends with something you approve in writing, and each approval is the point where the clock can stop without anyone noticing. Most samples arrive late because a decision was left open at one of those gates, not because the bench was slow.

Jewelry Sample Development, Step by Step

What jewelry sample development actually covers

The word "sample" gets used for three different things, and mixing them up is the first source of delay. A presentation sample is a piece pulled from existing production so you can hold it. A salesman sample is a one-off made for photography or a trade show. A production sample is the piece that fixes the specification for the order that follows.

Only the third is a contract. The first two are marketing, and neither tells you whether the design can be made repeatably at your price.

Step one: the brief and the drawing

A brief that lives in a chat thread will produce a sample that matches the thread and not your intention. What a factory needs before it draws anything: the piece type and finished size, the metal and alloy, the stone type, shape, size and count, the setting style, the clasp or finding, the finish, the target weight if you have one, and the market the piece is sold into.

Two things are usually missing and both cost a week. Tolerances — how much variation in dimension and weight is acceptable — and the priority order. If the piece has to hit a weight, say so. If it has to hit a look, say that instead. A factory cannot optimise both at once and will guess if you do not choose.

Step two: CAD and the model review

The CAD file is where the design becomes measurable. You should receive renders from three angles plus the top view, the dimensions, the metal volume and the stone list. Review at full size, not on a phone.

What to check: prong or bezel thickness at the bearing point, the gap under the stone, whether a band will sit flush, the shank thickness at the bottom where a ring wears fastest, and whether the stone seats match the actual stone measurements rather than the nominal size. Ask for a revision number. Every later conversation should quote it.

Step three: the master model and the mould

The approved file is grown or cut into a master, then a rubber or metal mould is made from it. This is the stage buyers most often skip, and it is the one that decides whether piece forty matches piece one. Ask to see the master before the mould is cut, and ask how the mould will be maintained — how many pulls before it is replaced, and who decides.

If you plan to reorder for years, the master is an asset. Ask who owns it and whether it is stored or destroyed if you move on.

Step four: casting the first piece

The first cast is a test of the file, the tree and the metal, in that order. Porosity, a short fill at a thin prong and a shrinkage oval on a wide band are all casting problems, not design problems, and all three are visible before any stone goes in.

Ask for the cast piece weighed against the CAD estimate and photographed at each stage. If the difference is large, the conversation belongs here, not after setting, when the piece is expensive to change.

Step five: setting, finishing and assembly

Setting is where the sample stops being a drawing. Stone seats that looked generous in CAD can be tight in metal, and prongs that looked correct in a render can sit high over a stone. Finishing then decides the surface: polished, matte, brushed, plated, or a combination on one piece.

Ask for photographs at each handover — set but unpolished, polished but unplated, finished. The middle one shows whether anyone cleaned up the interior of the piece.

Step six: the review and the revision round

Review the sample against the drawing, not against memory. Measure it, weigh it, count the stones, check the setting with a loupe, and wear it if it is wearable. Write every comment as a numbered item with a photograph attached, and separate "must change" from "would prefer".

A revision round is normal. Two is common. Three means the brief or the drawing was never agreed, and starting over costs less than the fourth round. When the sample is signed off, ask for a sealed second piece to be kept as the reference — that sealed piece is what production will be measured against later.

Why samples run late

The bench is rarely the bottleneck. Delay usually comes from a decision that was never made, and the cost of it surfaces weeks later at the shipping date.

Stage What usually slips How to prevent it
Brief Stone size or alloy left open "until we see it" Fix metal, stone and size before CAD starts
CAD review Comments come back in batches over two weeks One consolidated review with a deadline
Mould Master re-cut after approval Approve the master, not just the render
Casting Metal or stone not in stock Confirm material availability before the order
Setting Stones arrive late or to the wrong tolerance Ask who supplies stones and when they land

What a sample cannot tell you

A single sample proves that one piece can be made. It says nothing about the fortieth. Repeatability depends on the mould, the inspection routine and whether the same bench handles your order each time — questions that belong in a factory visit, not in a photo review.

It also cannot tell you the cost of the second order: sample pricing carries setup the production price will not, and assuming otherwise is how margins disappear.

Jewelry Sample Development, Step by Step

FAQ

How long does jewelry sample development take?

It depends on how many stages need a round trip. Ask your supplier for a stage-by-stage schedule in writing rather than one delivery date, so you can see which gate you are holding up.

Can I skip CAD and go straight to a hand-carved model?

You can, and for some organic shapes it is the better route. What you lose is the measurable file: no dimension list, no volume, no revision history, and no easy way to scale or modify the design later.

Do I have to pay for the sample?

Usually yes, and usually at more than the production unit price, because the setup is carried by one piece. Some factories credit part of it against a first order. Ask the question explicitly and get the answer before the sample is made.

Who owns the CAD file and the mould?

Whoever the agreement says. Default assumption is that the factory holds both. If the design is central to your brand, put ownership in writing before the master is cut, or budget for a new master when you leave.

What should I send with my comments on a sample?

Photographs with the problem circled, a measurement where a measurement applies, and a priority. "Prong too high, 0.4 mm over the stone, must change" is a usable comment. "Looks a bit off" is a week.

Holycome has built samples in Wuzhou, Guangxi since 2008, in an 8,000 square metre factory exporting to more than 100 countries. Development runs in 925 sterling silver, 9K to 18K gold and PT950, set with D colour VVS1 moissanite carrying a GRA certificate, IGI-certified laboratory-grown diamond, or laboratory-grown coloured stones. Send a drawing, a reference photo or a stone size to sales@holycome.com, or read how the process is scoped at our custom jewelry services page.

Leave a comment

All blog comments are checked prior to publishing
You have successfully subscribed!
This email has been registered