A Factory Audit Checklist for Jewelry Buyers

Quick answer: A jewelry factory audit is a scored walkthrough, not a relationship visit. You are there to establish four things: which processes the factory runs in-house, what the machines in the room can actually produce, how quality is checked before packing, and whether the workshop would survive an environmental inspection. Walk the floor before the meeting, follow one order through every stage, and write your score on the day. A supplier who resists the checklist has already told you something.

A Factory Audit Checklist for Jewelry Buyers

What a jewelry factory audit is actually for

Most buyers audit for reassurance, and reassurance is what a showroom is built to deliver. The useful purpose is narrower: find the gap between what a supplier says it does and what the building can support.

That gap is usually subcontraction, not fraud. A workshop with fifteen benches can cast, file and polish, then send plating, engraving and complex setting to three other buildings on the same street. The work comes back fine, but your delivery date now depends on three businesses you have never met, and a complaint has to travel through all of them.

The workshop walkthrough

Ask to walk the floor first and hold the meeting afterwards. A workshop at ten in the morning looks like a workshop: benches occupied, tools out of their slots, trays of work in progress. Count the benches and look at the floor beneath them.

Then follow a single order through the building. Pick a piece in production and ask to see it at each stage — model or mould, cast tree, filing bench, setting bench, polishing room, inspection table, packing bench. If a stage happens elsewhere, you want to hear it while standing in the room, not discover it in a shipping delay six weeks later.

Equipment: what has to be in the room

You are not grading brands. You are checking that the capability exists for the work you are buying.

  • Casting: melting equipment, a vacuum or centrifugal machine, and a burnout kiln with a programmable controller. Ask when the thermocouple was last checked.
  • Setting: bench pins in use, a microscope or a proper loupe station, and gravers that show wear. Unused gravers mean nobody sets stones here.
  • Polishing: separate wheels per metal, and dust extraction. Shared wheels cross-contaminate white and yellow gold; you see it as a grey haze on the surface.
  • Finishing: plating lines, a rhodium bath, laser marking — or a straight answer about where those happen and who controls them.
  • Measuring: a calibrated scale, callipers, ring gauges. Weights quoted to two decimals need a scale that justifies the second one.

In-house versus outsourced: the question that changes everything

Ask for the split as a share of a typical order, not as a yes or no. Very few factories do everything; the honest ones name their boundary.

Commonly outsourced: rubber mould making, rhodium plating, laser engraving, enamel, and setting on pieces with heavy pave work. None of that is disqualifying. What matters is control — who inspects the returned work, what happens when the subcontractor misses a date, and whether you are told before the order is placed rather than after.

Environmental compliance and wastewater

Jewelry finishing produces metal-bearing rinse water, spent plating baths, polishing dust and used investment plaster. All four have a disposal route, and the route is visible if you ask to see it.

A workshop with settling tanks, a filter press and a licensed handler collecting the sludge has thought about inspections. So has one that can show you the rinse cascade on the plating line and where the concentrate goes. A hose running from the polishing room to a yard drain answers the question just as well, and it should end the visit. Ask the same of dust: what is in the extraction bags, and who takes them.

The quality control paper trail

Ask to see a rejected piece from last month and the record that explains why. A factory that cannot produce one is not inspecting, it is looking.

Look for checks at more than one point. Cast weight against model weight catches porosity and short fills. Stone count and tightness after setting catches what reaches the customer. Dimension against the drawing catches shrinkage. Plating thickness, where plating is claimed, is measured or it is a guess. The last line should carry initials and a date, because a signature is the only part of a QC system that assigns responsibility.

Sample retention and traceability

Ask whether the factory keeps a sealed, approved sample of each order, for how long, where it is stored, and who may pull it. Ask whether the production record references a CAD revision number rather than a folder called "final".

This is the least glamorous item on the list and the one you will need most. When a customer complains in month eight, the sealed sample and the drawing revision are the only way to establish what changed and whether it changed at the factory or at your approval.

Scoring the audit

Score each section out of five on the day and write one sentence of evidence beside every score. A number without evidence becomes an opinion by the following week.

Section What a strong answer looks like Red flag
Workshop Benches occupied, work in progress, clean floor underneath Empty benches, staged trays, no scrap anywhere
Process ownership Named in-house stages, named subcontractors, inspection on return "We do everything" with no plating line in the building
Equipment Calibrated scale, controlled kiln, microscope at setting, extraction at polishing Equipment present but unplugged, or no consumables in stock
Environment Settling, filtration, licensed sludge handler, dust bags accounted for Rinse water to a yard drain, no waste documentation
Quality control Checks at casting, setting and final; signed and dated records Final visual check only, no rejection log
Traceability Sealed samples archived, records tied to drawing revisions "We keep the last one on the bench"

A Factory Audit Checklist for Jewelry Buyers

FAQ

How long should a jewelry factory audit take?

Half a day covers a moderate workshop if you walk the floor and follow one order. Two days is better before a first order, because it leaves time to read the quality records and the environmental paperwork rather than glance at them.

Should I announce the audit in advance?

Yes, for a first visit. Unannounced inspections belong in a supply agreement, once you have a relationship and a clause that permits them. Announced visits still expose subcontraction, because the order you follow is already in production.

Do I need an independent auditor?

For compliance and social auditing, usually yes — the report is only worth something if a third party signs it. For capability, a buyer who knows the process sees more in an afternoon than a generalist sees in a week.

What if the factory fails one section?

Score it, price the risk, and decide whether you can inspect around it. A missing plating line can be managed with incoming checks. Untraceable samples and no rejection log cannot, because you will have no evidence when something goes wrong.

Does a good audit guarantee good production?

No. It tells you the capability and the control system exist. Whether they are applied to your order is a question of capacity and supervision, which is why a first order should be small enough to inspect in full.

Holycome has run its own floor in Wuzhou, Guangxi since 2008 — 8,000 square metres, exporting to more than 100 countries, with 708 pieces listed on the site in 925 sterling silver, 9K to 18K gold and PT950. Visitors are welcome by appointment, and we will walk this same checklist with you, including the stages we do not do in-house. Write to sales@holycome.com, or start with the custom work at our custom jewelry services page.

Leave a comment

All blog comments are checked prior to publishing
You have successfully subscribed!
This email has been registered