Setting Cost by Style: Where the Labour Goes

Four silver rings in a row: plain four-prong solitaire, bezel, halo, and a pavé band, lit from above
Same metal, same stone, four amounts of bench time. The fourth ring is not twice the first.

Quick answer: In sterling silver, the middle half of our catalogue runs from $72 to $165 — a spread of 2.29× on the same metal. That spread is almost entirely labour. A solitaire sets one stone with four to six prongs; a halo sets a centre plus a ring of small stones, each with its own beads or prongs; pavé sets dozens at a microscope. Since the stone is under a quarter of a typical piece, the hours are what you are actually buying, and style choice moves the price more than metal choice does.

Where the bench time goes in four common settings, and why the cheapest-looking ring is often the one that took longest.

Why labour is bigger than buyers expect

Buyers price a ring as metal plus stone plus a bit for making it. The proportions are the other way round. Our loose-stone median is $23.14 against a $95.42 median piece, so the stone is a little under a quarter, and the metal in a silver ring is worth a small fraction more. What remains — most of the invoice — is hours.

This has one consequence that surprises people: labour is charged at the same rate whatever the metal. A setter's hour costs the same on sterling as on platinum. In silver, where the material is nearly free, labour's share of the price is at its highest.

The four styles, and what each one demands

Style Bench work What drives the hours
Four or six-prong solitaire Seat cut, prongs raised, stone set, tips filed and polished Getting the seat square; nothing hides a bad seat
Bezel Wall raised or forged, stone seated, wall burnished over the girdle The wall must close evenly all the way round
Halo Centre set, halo built or cast, each small stone set individually Stone count, and keeping the ring of stones level
Pavé band Seats drilled, beads raised, each stone set under magnification, surface re-polished Dozens of stones, each one a separate operation

Read the third column as a multiplier: a solitaire is one setting, while a pavé band repeats that operation across the whole visible surface.

Bezel: the work you cannot see

A bezel looks simpler than a solitaire and is not. The wall has to be raised to the right height, the stone seated so the girdle sits just below the rim, and the metal pushed over it evenly around the full circumference. Too much pressure and the stone chips; too little and it rattles. What you buy is protection: nothing catches, nothing lifts a prong, and the stone cannot be lost by snagging.

Halo: the arithmetic of small stones

A halo is a ring of small stones around the centre. Each one needs a seat, a pair of beads or four tiny prongs, and a check that its table sits level with its neighbours. Twenty small stones is twenty operations, and the failure mode is cumulative: one stone set a fraction low makes the whole ring look wrong from across a table.

The economic oddity: halo stones are cheap and halo labour is not. You pay for repetitions, then pay again for a re-polish that must avoid every bead.

Pavé: microscope work

Pavé sets stones flush into the surface, held by beads raised from the metal between them. It is done under magnification, at a bench, with a graver and a beading tool. A band with forty stones has eighty beads, and each bead is raised, shaped and checked.

This is the most labour-dense common setting, and cheap manufactures shortcut it: glue, or cast-in imitation beads, both of which photograph acceptably and fail within a year. Ask whether the beads are raised or cast.

Prongs are cheap to make and expensive to get right

A four-prong head is a casting that costs almost nothing; the work is in the seat. The bearing must be cut level, the prongs must meet the girdle at the right point, and the tips must be filed to hold without a sharp edge. Two solitaires at $72 and $165 can look identical in a listing: one has a seat cut in a jig, the other prongs bent over roughly. Invisible on day one, obvious in year two.

What the $72 to $165 spread buys

Style Stones set by hand Where it sits in the silver band
Prong solitaire, plain band One Bottom, near $72
Bezel One Lower middle
Halo with a plain shank Fifteen to thirty Upper middle
Halo with pavé shoulders Forty and up Top, near $165

Put the two spreads side by side and the argument makes itself. Moving from silver to 14K raises our median by 88.9%, from $97.11 to $183.46. Moving from a prong solitaire to a halo with pavé shoulders moves a silver piece by up to 129%, from the bottom of the band to the top. Style is the bigger lever, and unlike metal it is a lever you can choose without changing how the piece wears.

Where the labour sits in the total

Take the median piece at $95.42. The stone is about $23 and the metal is small; the rest is bench, polish, setting, checking and handling. That is the number to interrogate when a price looks too low — not the stone, which is a commodity with a published market, but the hours, which are not. A cheap halo has a cheap halo's labour in it: the stones will be there on delivery, and the question is what holds them in year three.

FAQ

Is a bezel cheaper than a solitaire?

Usually a little dearer, not cheaper. Fewer parts, more careful work: the wall has to close evenly around the girdle, and there are no prongs to adjust afterwards if it does not.

Why does pavé cost so much when the stones are tiny?

You pay per operation, not per carat: each stone needs a seat, two beads and a check under magnification.

Can a cheap setting be re-worked later?

Sometimes. Prongs can be re-tipped and loose stones re-seated, but cast-in imitation beads cannot become real pavé, and a badly cut seat usually needs a new head.

Does the setting style affect the stone I can use?

Yes. A bezel hides the girdle and suits a shallower stone; a halo flatters a small centre by adding apparent diameter; four prongs show the most stone and hide the least.

What we make

We have run our own factory in Guangxi since 2008, so the setting is done by people we employ rather than by a subcontractor we have never met. We cast and finish in 925 sterling silver, 9K, 14K and 18K gold, and PT950 platinum, with GRA-certified D-colour VVS1 moissanite or IGI-certified lab-grown diamond. Across 708 listings, prices run from $17 to $2,020, median $95.42; in silver the middle half sits between $72 and $165.

Shipping is free over $99 and $5.99 below it, with 30-day returns on unworn pieces in original packaging. If you are choosing between styles, ask us how many stones a design sets by hand and whether the beads are raised — the answers separate a $72 ring from a $165 one better than any photograph. We ship direct from the factory, so clearance times are outside our control.

Leave a comment

All blog comments are checked prior to publishing
You have successfully subscribed!
This email has been registered