Casting, Stamping and Hand-Fabrication
Quick answer: The three jewelry production methods split by quantity and by shape. Casting suits complex, organic and hollow forms from a few dozen pieces upward, because one mould serves the whole run. Stamping suits flat, repetitive parts — tags, plates, links, earring bodies — at high volume, where a steel die pays for itself over thousands of strikes. Hand-fabrication suits one-offs, heavy solid pieces and anything with a mechanism, and it is the method that fixes what the other two cannot make.

Most production arguments are really method arguments. A design that looks simple on a screen may be unmakeable by the method the quotation assumed, and the fix is usually a different process rather than a different price.
What lost-wax casting actually does
A master model is moulded in rubber, wax is injected into the cavity, the waxes are treed, invested in plaster and burned out, and metal is drawn in under vacuum or pressure. The tree is then cut, the pieces cleaned, and the surfaces finished by hand.
The economics are in the mould: one rubber mould carries hundreds of shots, so the cost per piece falls quickly after the first run. What casting buys you is shape freedom — undercuts, hollow interiors, organic texture, a bezel that wraps a stone — because the wax is destroyed to release the piece, not pulled out of a die.
What stamping actually does
Sheet or strip is fed into a press and cut or formed between a punch and a die. Simple blanking cuts a silhouette; coining presses a relief into the face; progressive dies do several operations in one pass, including piercing, bending and edge rounding.
Stamping buys consistency and speed, not shape freedom. Wall thickness is whatever the sheet is, which is excellent for weight control, and the edges are sheared rather than cast, so they are crisp and square. What it cannot do is an undercut, a hollow, or a form that needs the metal to flow in two directions at once without a second operation.
What hand-fabrication actually does
Sheet, wire and tube are cut, annealed, formed, soldered, forged and set at a bench. There is no mould and no die, which means no tooling cost and no minimum beyond the bench time you are willing to pay for.
It is the only method that handles real one-offs well, and the only one that can produce certain structures at all: heavy hand-forged bangles, tension settings, articulated mechanisms, anything where the metal's own spring or taper is part of the design. It is also the most expensive per piece at any volume, and the least repeatable — two bench-made pieces are siblings, not twins.
| Method | Best at | Volume economics | Main limitation |
|---|---|---|---|
| Casting | Complex, hollow, organic, stone-set forms | Mould cost amortises quickly; per-piece cost drops after the first run | Porosity, shrinkage, finishing labour on every piece |
| Stamping | Flat or shallow-formed repetitive parts | High die cost, very low per-piece cost at volume | No undercuts or hollows; geometry must suit the press |
| Hand-fabrication | One-offs, heavy solid work, mechanisms | No tooling; per-piece cost stays flat as volume rises | Slow, variable, hard to scale and hard to repeat exactly |
Tooling cost and the minimum viable quantity
The mould is a one-off cost, modest in absolute terms. The die is a much larger commitment in money and lead time, because steel has to be cut, hardened and tried. That is why casting makes sense from the dozens upward and stamping only makes sense at volume.
Amortisation is what then changes the quotation. A mould that carries a long run spreads its cost thinly across thousands of pieces; a die that wears out after a known number of strikes has to be replaced inside the life of a popular design, and that replacement is a real cost of the second year, not the first order. Ask which of those you are paying for.
Ask what tooling is being quoted and who owns it before you approve a price.
Surface, edge and the look of each process
Cast surfaces carry a slightly granular skin that needs polishing back, and thin sections can show porosity that only appears after the final polish — the most expensive moment to find it. Stamped surfaces come off the die clean and consistent, with sharp edges that read as industrial rather than hand-made.
Hand-fabricated work shows tool marks, slight asymmetry and a taper or draw that no mould reproduces. Buyers who want a piece to look made rather than manufactured are usually asking for the third process, whether they know it or not.
Weight, hollow structure and how a piece feels
Casting can make a hollow form that weighs a fraction of its visual volume, which is how large pendants and bold hoops stay wearable in gold. Stamping gives uniform thickness across a part, so a stamped tag or plate is exactly as heavy as the sheet says.
Hand-fabrication is the method for heft. A forged bangle is dense because it has been hammered, not cast, and the difference is obvious in the hand. If your product's selling point is weight, the process is part of the specification.
Design constraints worth knowing before you draw
Casting needs wall thickness that will fill, and it shrinks as it cools, so a dimension on the drawing is not the dimension in the mould cavity. Stamping needs draft, no undercuts, and a form that releases; a 90-degree internal corner will tear or need a second operation.
Hand-fabrication needs joints that can be soldered without destroying a previous one, and assemblies that can be held while the solder flows. Designers who learn these three rule sets stop specifying impossible pieces.
Mixing jewelry production methods in one product
Most real products are hybrids. A cast pendant hangs from a drawn or stamped chain, carries a stamped tag, and closes with a finding that was pressed by the thousand. A hand-fabricated bangle may carry a cast end cap.
Choosing per component rather than per product is where cost comes out of a design without changing how it looks. It is also how a small brand gets a distinctive silhouette at a workable price.

FAQ
Which of the jewelry production methods suits a first run?
Casting, for most designs. The tooling commitment is small relative to stamping, and it tolerates changes better if the first samples are not quite right.
Is stamped jewelry lower quality than cast?
No, it is a different construction. Stamped parts are usually more consistent and more accurate; they simply cannot carry the shapes casting can.
Can a cast piece be made to look hand-made?
Partly. Texture and finish can be reproduced from a hand-made master, but the slight variation between pieces cannot. Buyers notice the repetition at close range.
Why does my design cost more than expected?
Usually a feature that forces a second operation: an undercut, a hollow, a sharp internal corner, or a stone set where the mould cannot reach.
Can the same design move between methods later?
Sometimes, at the cost of a new tool. Moving from cast to stamped usually requires simplifying the form; moving the other way requires accepting a thicker section.
We cast, stamp and hand-finish under one roof in Wuzhou, which means a design can be quoted on the method that actually suits it rather than the one the factory happens to own. Send the drawing to sales@holycome.com, or start from our custom jewelry services page.
If you are sourcing this for a production run, send your spec through our custom jewelry services page or write to sales@holycome.com">sales@holycome.com. We answer Monday to Saturday, 09:00–18:00 GMT+8.