Pave vs Plain Band: Where the Money Goes

A pavé-set band and a plain polished band lying side by side on dark stone
Two bands of the same width. One carries thirty seats drilled into the shank.

Quick answer: On a pavé band the money goes into setting hours and a lot of very small stones — not into better metal or a bigger look. On a plain band it goes into metal alone, which is why the plain band is the more repairable and more resaleable object. In our catalogue the median 925 silver piece is $97.11 and the median 18K piece is $345.80, so the metal is where the real money sits; pavé spends its budget on labour, which is the one thing that does not survive the decade.

Own-catalogue figures, 17 November 2026, 708 pieces in stock: median $95.42, interquartile range $72.56–$164.91, range $66.65–$169.26. 480 of the 708 pieces are sterling silver. No competitor prices are used.

What pavé actually is

Pavé is a surface covered in small stones set close together, each held by tiny beads of metal raised from the surface rather than by claws. The effect is continuous sparkle with almost no visible metal between the stones — and that description is also the bill of materials: a shank wide and thick enough to carry seats, a hole drilled for each stone, a seat cut at the right diameter, a stone dropped in, metal pushed over the edge to hold it. Thirty stones means thirty of those, under a loupe.

The three lines in a band's price

Line Plain band Pavé band
Metal Full weight of the shank Similar, but drilled and thinned at the seats
Stones None Twenty to forty, a millimetre or so each
Labour Casting, filing, polishing Casting, plus a seat and a setting per stone, plus finishing around them
Recoverable at resale The metal, near enough The metal, less what the drilling removed

Notice what is missing from the pavé column: any claim that the stones are valuable. Small melee is worth little per stone and almost nothing secondhand; what you buy is the arrangement, and the arrangement is labour.

Setting hours are the real line

A plain band leaves the bench after casting, filing and polishing. A pavé band leaves after all that plus one drilled hole, one cut seat, one set stone and one raised bead per stone — and the beads must be uniform, or the line of sparkle goes wavy and the effect collapses. That is also why cheap pavé looks cheap: stones set too low sit dark, beads heavy enough to swallow the table are visible at arm's length. The labour is not decoration on top of the cost; it is the cost.

Thin bands and the compromise nobody states

Pavé needs wall. A band under about 2mm wide has little room for a seat before the drill breaks through the inside of the shank, and a band under about 1.5mm at the base has no structural margin left once it is drilled. A 1.5mm pavé band is not a thin version of a 3mm one — it is a band that has traded its strength for its surface, and it will oval, dent and shed stones in a way a plain band of the same width will not.

The hidden cost: resizing

This is where pavé quietly gets expensive. Sizing a ring means cutting the shank at the base, spreading or closing it, then re-soldering and refinishing — routine, repeatable and invisible on a plain band.

On a pavé band the base is usually left plain for exactly this reason — a small gap in the stones. Size within that allowance and nothing happens. Go beyond it and the shank moves where the stones are: the curve changes, the drilled seats no longer sit square to the surface, and beads that were tight open up. Each loosened stone is a bench job, and the bench job costs more than the resize did. The practical rule is one size comfortably on pavé, two or three on plain, with a full re-shank as the fallback that only a plain band has.

Why the plain band holds value

A plain band is metal, and metal is the only part of any ring that reliably has a buyer secondhand — no stones to grade, no settings to inspect. It is also the cheapest thing to refurbish: polish it and it looks new. Pavé is the opposite. The value sits in work that cannot be recovered: thirty seats drilled into a shank are thirty holes a future owner did not ask for, the stones are worth little individually, and the labour disappears the moment the piece leaves the bench.

Where pavé is worth the money

When the band is the design: a wedding set where the band reads as a band of light, a stack where pavé contrasts a plain engagement ring. And when the ring will not be resized or worn hard — pavé at a desk is fine for twenty years; the same band on someone who gardens will lose stones one repair at a time.

Matching the band to the wear

If this describes you Choose Because
Hands-on work, gym, gardening Plain, 2mm or wider No seats to lose, no thin wall
Desk work, occasional wear Pavé at 2.5mm or wider Enough wall for the seats
Likely to resize within a year Plain Two to three sizes, or a full re-shank
Stacking with other rings Half-pavé or plain Stones rub against neighbours
Buying for resale value Plain, in gold Metal is the only recoverable part

FAQ

Is pavé worth the extra cost?

If the band is the design and the ring will not be worn hard, yes — you are buying labour and a specific look, and you get both. If you want durability and resale value, no: the money is in work that cannot be recovered.

Can a pavé band be resized?

Usually one size, because the base of the shank is left plain for that purpose. Beyond that, the seats and beads around the stones are disturbed and stones loosen. A plain band takes two or three sizes, or a re-shank.

Does a pavé band wear out?

The stones do not; the beads holding them do: metal wears at the high points, and a thinning bead will eventually let a stone go. Expect stones tightened every few years on a daily band.

Why is a plain band a better investment?

Because it is almost entirely metal, and metal is the only part of any ring with a reliable secondhand buyer. At our medians a plain 18K piece is $345.80 against $97.11 in silver — material that still exists years later.

What we make

We cast and finish in our own factory in Guangxi, which we have operated since 2008, in 925 sterling silver, 9K, 14K and 18K gold, and PT950 platinum. Stones are GRA-certified D-colour VVS1 moissanite at 9.25 on the Mohs scale, or IGI-certified lab-grown diamonds. Bands are specified by width and base thickness in millimetres, and pavé bands state the stone count rather than a total carat weight.

Shipping is free over $99 and $5.99 below it. Returns run 30 days on unworn pieces in original packaging, excluding custom and engraved work. If you are choosing between pavé and plain, order the plain band in the width you want first — it tells you whether the width suits your hand before you pay for thirty seats in it.

Leave a comment

All blog comments are checked prior to publishing
You have successfully subscribed!
This email has been registered