Cast vs Handmade: What the Difference Actually Is

A wax model on a bench beside the finished cast ring and a hand-sawn sheet of silver
The wax is the design; the casting is a copy, and never quite the original.

Cast and handmade are usually presented as a hierarchy, handmade on top and casting as the cheap option. That is a marketing arrangement, not a metallurgical one. Both produce good jewellery and bad, and the differences that matter are in repair, consistency and what happens at the edge of a prong.

Two processes, not two classes

Casting is a reproduction method: a model is made once and copies are produced from it. Hand-fabrication is a construction method: built from sheet, wire and tube, joined with solder, shaped with files and hammers. Most commercial jewellery is cast; most one-off commissions are fabricated. Expensive pieces are often cast then hand-finished, which muddles the argument: finishing by hand does not make a piece handmade.

Lost-wax casting, in order

A model is made in wax, carved or printed from a CAD file. It is sprued, attached to a central channel, and invested in plaster that sets around it. The cylinder is heated so the wax melts out, leaving a cavity in the exact shape of the model. Molten metal is forced in by vacuum or centrifuge, and once cool the plaster is broken away and the tree of castings cut free, cleaned and polished.

The whole piece forms in one operation: complex detail comes out in a single pour at a cost hand-building could never approach.

What hand-fabrication involves

Sheet is cut with a saw, bent, filed and soldered. Wire is drawn, formed and hardened by hammering. Settings are built from strip and burred by hand. Every joint is a separate operation with its own heat, and the metal is worked repeatedly, which hardens it. Nothing is reproduced, so nothing is tooled — one-off work is possible, repeat work expensive, because the second piece costs as much as the first.

Consistency versus trace

A cast run is consistent: piece 47 and piece 412 are the same ring, which is what a customer ordering from a photograph needs. Consistency also reproduces a flaw — if the model has a soft edge, every copy has it.

Fabricated work carries the maker's marks — a hammer texture that varies, a solder seam you can find with a fingernail, a prong slightly thicker on one side. Some is character, some a mistake a casting would have averaged out.

Working metal hardens it, and a forged shank is denser than a cast one of the same section. But a fabricated piece soldered repeatedly has annealed zones next to hard ones, and that boundary is where a crack starts.

Porosity, and the edge of a prong

Casting's real weakness is internal. Metal shrinks as it solidifies, and where a section is thick with no feed of molten metal behind it you get micro-voids — porosity. Invisible until the piece is polished through, or until a prong snaps instead of bending. Thin cast prongs are the classic failure.

Fabricated prongs are formed from wire with a grain direction, so they bend rather than shatter. On the other side, a fabricated band with a hard-soldered seam can split under stress where a cast band has no seam at all. Well-made pieces usually mix the two, and it is fair to ask which part is which.

Property Cast Hand-fabricated
Repeatability Identical across a run Every piece differs
Complex detail Cheap to include Costly and slow
Internal flaws Porosity possible in thick sections None; solder seams instead
Resizing a band Straightforward, about two sizes Straightforward if the seam is accessible
Rebuilding a prong Easier; matching stock is poured Easier to shape in place
Chipping at an edge Can spall where porosity reaches the surface Bends; cracks at a hardened seam
Cost of one piece Model plus mould, then low unit cost Bench hours, no tooling

Which repairs more easily

Casting is generally easier to repair in the ordinary sense: a damaged section is cut out, new metal poured from the same mould or built up with solder, and the join polished back. The risk is that repair metal and surrounding metal differ in density, and re-polishing reveals a shade difference.

Fabricated work repairs well too, but needs a bench that knows where the hard solder was — reheating to fix one joint can loosen another. A good repairer prefers whichever construction they can see, which is why an honest seller says how a piece was made.

Where the price difference comes from

Not from the metal — the metal is the same. It comes from labour hours per piece, tooling amortised across a run, and finishing. A cast ring off a production run carries perhaps twenty minutes of bench time; a fabricated one carries two to six hours. The variable not on that list is care, and a cheap casting with clean sprue removal and a proper polish beats a rushed fabrication every time.

What we make

We cast in our own factory in Guangxi, which we have operated since 2008, in 925 sterling silver, 9K, 14K and 18K gold, and PT950 platinum, with settings assembled and finished by hand at the bench. Stones are GRA-certified D-colour VVS1 moissanite or IGI-certified lab-grown diamonds. Prices run from $17 to $2,020, with a typical piece around $98 — a range set by metal and by hours, not by a label.

Shipping is free over $99 and $5.99 below. Returns run 30 days on unworn pieces in original packaging, and because we make the pieces we can tell you how any given one is built if you ask before ordering. We ship direct from the factory, so clearance time is outside our control; size and metal are the things worth settling first.

Leave a comment

All blog comments are checked prior to publishing
You have successfully subscribed!
This email has been registered